View LM5015-14_9037537.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

lm5015 www.ti.com snvs538b ? november 2007 ? revised january 2009 lm5015 high voltage monolithic two-switch forward dc-dc regulator check for samples: lm5015 1 features description the lm5015 high voltage switch mode regulator 2 ? dual integrated 75v n-channel mosfets features all the functions necessary to implement ? ultra-wide input voltage range: 4.25v to 75v efficient high voltage two-switch forward and two- ? integrated high voltage bias regulator switch flyback regulators, using a minimum of external components. this easy to use regulator ? adjustable output voltage integrates high side and low side 75 volt n-channel ? 1.5% feedback reference accuracy mosfets with a minimum 1 amp peak current limit. ? current mode control with selectable the voltage across the mosfets employed in the compensation two-switch topology is clamped to the input voltage, allowing the input voltage range to approach the ? wide bandwidth error amplifier rating of the mosfets. the regulator control method ? integrated current sensing and limiting is based on current mode control providing inherent ? 50% maximum duty cycle limit ease of loop compensation and line feed-forward for superior rejection of input transients. ? single resistor oscillator programming ? oscillator synchronization capability the operating frequency is set with a single resistor and is programmable up to 750 khz. the oscillator ? programmable soft-start can also be synchronized to an external clock. ? enable / under-voltage lockout (uvlo) pin additional protection features include cycle-by-cycle ? thermal shutdown current limiting, thermal shutdown, under-voltage lockout and remote shutdown capability. the device package is available in the htssop-14ep package featuring an exposed die attach pad to enhance thermal ? htssop-14ep (exposed pad) dissipation. typical application schematic 1 please be aware that an important notice concerning availability, standard warranty, and use in critical applications of texas instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. 2 all trademarks are the property of their respective owners. production data information is current as of publication date. copyright ? 2007 ? 2009, texas instruments incorporated products conform to specifications per the terms of the texas instruments standard warranty. production processing does not necessarily include testing of all parameters. isolated feedback vin ho ss comp gnd rt vcc lm5015 bst en fb lo pgnd pvin isolated output input (4.25v - 75v)
lm5015 snvs538b ? november 2007 ? revised january 2009 www.ti.com connection diagram htssop-14 ep package top view pin descriptions pin name description application information 1 agnd analog ground internal reference for the regulator control functions. the agnd pin and the pgnd pin should be connected directly to minimize switching noise and prevent erratic operation. 2 rt oscillator frequency programming the internal oscillator is set with a resistor between this pin and the agnd pin. and optional synchronization input the recommended switching frequency range is 25khz to 750 khz. the rt pin can accept synchronization pulses from an external clock. a 100 pf capacitor is recommended for coupling the synchronizing clock to the rt pin. 3 fb feedback input of the internal error this pin is connected to the inverting input of the internal error amplifier. the amplifier, for non-isolated 1.26v reference is internally connected to the non-inverting input of the error applications amplifier. in isolated application using an external error amplifier, this pin should be connected to the agnd pin. 4 comp control input for the pwm internally connected to the open drain output of the internal error amplifier. comparator comp pull-up is provided by an internal 5 k ? resistor which may be used to bias an opto-coupler transistor in isolated applications. 5 cfb current feedback pin feedback in put for high bandwidth isolated applications. an npn current mirror couples the external opto-coupler current to the pwm comparator while maintaining a relatively constant opto-coupler voltage. 6 pgnd power ground internally connected to the current sense resistor in the source of the low side mosfet switch. 7 lo low side switch drain the drain terminal of the internal low side power mosfet. 8 pvin input supply pin for high side switch internally connected to the drain of the high side power mosfet. 9 ho high side switch source the source terminal of the high side power mosfet. 10 bst high side bootstrap bias an external capacitor is required between the bst and the ho pins. a minimum capacitor value of 0.022 f is recommended. the capacitor is charged from vcc via an internal diode during the power mosfet off-time. 11 vcc bias regulator output, or input for vcc tracks vin up to 6.9v. at higher vin voltages, vcc is regulated to 6.9 external bias supply volts. a 0.47 f or greater ceramic decoupling capacitor is required on the vcc pin. an external bias voltage between 7v and 14v applied to the vcc pin will disable the internal vcc regulator, reduce internal power dissipation, and improve the converter efficiency. 12 vin analog input voltage pin power supply input for the switching regulator control blocks. 13 en enable / under-voltage lock-out / an external voltage divider can be used to set the input under-voltage lockout shutdown input threshold. if the en pin is left unconnected, a 6 a pull-up current source pulls the en pin high to enable the regulator. 14 ss soft-start an internal 11 a current source charges an external capacitor connected to the ss pin to soft-start the switching regulator by gradually raising the comp pin voltage. na ep exposed pad exposed metal pad on the underside of the package. it is recommended to connect this pad to the pgnd and agnd pins, and also to the pc board ground plane in order to improve heat dissipation. 2 submit documentation feedback copyright ? 2007 ? 2009, texas instruments incorporated product folder links: lm5015 1 23 4 bst vcc comp lo pgnd cfb ho pvin 5 10 fb vin 6 9 rt en 7 8 agnd ss 11 12 13 14 ep
lm5015 www.ti.com snvs538b ? november 2007 ? revised january 2009 these devices have limited built-in esd protection. the leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the mos gates. absolute maximum ratings (1) (2) v in to agnd 76v bst to agnd 90v pvin to ho, lo, pgnd 76v ho to pgnd (steady state) -3v to 76v lo to pgnd (steady state) -0.3v to 76v bst to vcc 76v bst to ho 14v v cc , en to agnd 14v comp, fb, rt, ss to agnd -0.3v to 7v pgnd to agnd -0.3v to +0.3v cfb sink current 10 ma maximum junction temperature 150 c storage temperature ? 65 c to + 150 c esd rating human body model (3) 2 kv (1) absolute maximum ratings are limits beyond which damage to the device may occur. operating ratings are conditions under which operation of the device is intended to be functional. for guaranteed specifications and test conditions, see the electrical characteristics. (2) if military/aerospace specified devices are required, please contact the texas instruments sales office/distributors for availability and specifications. (3) the human body model is a 100pf capacitor discharged through a 1.5 k ? resistor into each pin. test method is per jesd-22-a114. operating ratings v in 4.25v to 75v operation junction temperature ? 40 c to + 125 c copyright ? 2007 ? 2009, texas instruments incorporated submit documentation feedback 3 product folder links: lm5015
lm5015 snvs538b ? november 2007 ? revised january 2009 www.ti.com electrical characteristics limits in standard type are for t j = 25 c only; limits in boldface type apply over the junction temperature (t j ) range of ? 40 c to + 125 c. minimum and maximum limits are guaranteed through test, design, or statistical correlation. typical values represent the most likely parametric norm at t j = 25 c, and are provided for reference purposes only. v vin = 48v, r rt = 31.6 k ? unless otherwise stated. see (1) . symbol parameters conditions min typ max units startup regulator v vcc-reg vcc regulator output 6.35 6.85 7.25 v vcc current limit v vcc = 6v 20 25 ma vcc uvlo threshold vcc increasing, vin = vcc, en=open 3.45 3.75 4.05 v vcc uvlo hysteresis vin = vcc, en = open 0.15 v bias current (iin) v fb = 1.5v 3.1 4.5 ma i q shutdown current (iin) v en = 0v 110 170 a en thresholds en shutdown threshold v en increasing 0.25 0.45 0.65 v en shutdown hysteresis 0.1 v en standby threshold v en increasing 1.19 1.26 1.3 v en standby hysteresis 0.1 v en current source 6 a mosfet characterstics low side mosfet rds(on) plus i d = 0.6a 0.49 0.93 ? current sense resistance mosfet leakage current v lo = 75v 0.05 5 a high side mosfet rds(on) i d = 0.6a 0.45 0.90 ? mosfet leakage current v pvin = 75v, v ho = pgnd 0.05 5 a total gate charge including both v vcc = 8v 9 nc low and high side mosfets pre-charge switch on voltage i d = 1 ma 0.82 v including series blocking diode current limit i lim cycle by cycle current limit 1 1.2 1.4 a cycle by cycle current limit delay 130 ns oscillator f sw1 frequency1 r rt = 31.6k 180 200 220 khz f sw2 frequency2 r rt = 15.4k 365 405 445 khz v rt-sync sync threshold v rt increasing 3.2 v sync pulse width minimum v rt > v rt-sync + 0.5v 15 ns pwm comparator maximum duty cycle 49 % min on-time v comp > v comp-os 140 ns min on-time v comp < v comp-os 0 ns v comp-os comp to pwm comparator offset 0.9 1.3 1.55 v error amplifier v fb-ref feedback reference voltage internal reference, v fb = v comp 1.236 1.26 1.274 v fb bias current 10 na dc gain 72 db comp sink current v comp = 250mv 2 ma comp short circuit current v fb = 0, v comp = 0 0.9 1.2 1.5 ma comp open circuit voltage v fb = 0 4.5 5.15 5.95 v (1) min and max limits are 100% production tested at 25 c. limits over the operating temperature range are guaranteed through correlation using statistical quality control (sqc) methods. limits are used to calculate national ? s average outgoing quality level (aoql). 4 submit documentation feedback copyright ? 2007 ? 2009, texas instruments incorporated product folder links: lm5015
lm5015 www.ti.com snvs538b ? november 2007 ? revised january 2009 electrical characteristics (continued) limits in standard type are for t j = 25 c only; limits in boldface type apply over the junction temperature (t j ) range of ? 40 c to + 125 c. minimum and maximum limits are guaranteed through test, design, or statistical correlation. typical values represent the most likely parametric norm at t j = 25 c, and are provided for reference purposes only. v vin = 48v, r rt = 31.6 k ? unless otherwise stated. see (1) . symbol parameters conditions min typ max units comp to sw delay 50 ns unity gain bandwidth 4 mhz soft start soft-start current source 8 11 14 a soft-start to comp offset 0.3 0.5 0.7 v thermal shutdown t sd thermal shutdown threshold 165 c thermal shutdown hysteresis 25 c thermal resistance jc junction to case 6.6 c/w ja junction to ambient 40 c/w copyright ? 2007 ? 2009, texas instruments incorporated submit documentation feedback 5 product folder links: lm5015
lm5015 snvs538b ? november 2007 ? revised january 2009 www.ti.com typical performance characteristics demo-board efficiency vfb vs vs i out and v in temperature figure 1. figure 2. iq (non-switching) vcc vs vs vin vin figure 3. figure 4. rds(on) ien vs vs vcc vin vs vs temperature temperature figure 5. figure 6. 6 submit documentation feedback copyright ? 2007 ? 2009, texas instruments incorporated product folder links: lm5015 -50 0 50 100 150 i en ( p a) temperature (c) 3 4 5 6 7 vin = 4.25v 10v 48v -50 150 0.2 0.3 0.4 0.5 0.6 0.7 0.8 r ds(on) ( : ) temperature (c) 0 50 100 low side r ds(on) + r cs vcc = 12v 8v 4.25v high side r ds(on) vcc = 4.25v 8v 12v 0 2 4 6 8 v cc (v) v in (v) 0 2 4 6 8 0 20 40 60 80 i q ( p a) v in (v) 0 50 100 150 200 -50 0 50 100 150 v fb (v) temperature (c) 1.24 1.25 1.26 1.27 1.28 0 0.5 1 1.5 2.0 2.5 3.0 load current (a) 70 75 80 85 90 efficiency (%) v in = 36v v in = 48v v in = 72v f sw = 300 khz v out = 5.0v
lm5015 www.ti.com snvs538b ? november 2007 ? revised january 2009 typical performance characteristics (continued) ilim vs ilim vcc vs vs vcc temperature figure 7. figure 8. fsw fsw vs vs r rt temperature figure 9. figure 10. fsw vs vcc error amplifier gain/phase figure 11. figure 12. copyright ? 2007 ? 2009, texas instruments incorporated submit documentation feedback 7 product folder links: lm5015 1 10 100 1000 10000 frequency (khz) -10 0 10 20 30 40 50 60 70 gain (db) phase ( ) -120 -90 -60 -30 0 30 60 90 120 gain phase -50 0 50 100 150 frequency (khz) temperature (c) 190 195 200 205 210 10 100 1000 10 100 1000 frequency (khz) r t (k : ) -50 0 50 100 150 ilim (a) temperature (c) 1.1 1.15 1.2 1.25 1.3 vcc = 7v vcc = 14v vcc = 4.25v 2 4 6 8 10 12 14 v cc (v) 0.0 1.4 ilim (a) 0.2 0.4 0.6 0.8 1.0 1.2 temperature = 25c 2 4 6 8 10 12 14 v cc (v) 180 185 190 195 200 205 210 frequency (khz)
lm5015 snvs538b ? november 2007 ? revised january 2009 www.ti.com block diagram figure 13. 8 submit documentation feedback copyright ? 2007 ? 2009, texas instruments incorporated product folder links: lm5015 oscillator with sync capability vin lo driver pwm comparator rt logic vcc vcc ldo en current limit pgnd current sense 6 p a shutdown 1.26v standby vcc vcc uvlo leading edge blanking (leb) thermal limit vcc a = 30 v/v enable disable reference generator gate drive uvlo level shift enable clk max duty cfb 11 p a ss s r q driver ho pvin bst enable enable vdd fb comp maximum on time on time delay max duty on time delay 5k 42 m : i 42 mv/a v = 1.25v/a 0.45v 3.7v 1.26v vdd (+5 v ) 1.3v vdd (+5 v ) clk (50% duty) (165c) 1.26v 1.5v agnd + - + -
lm5015 www.ti.com snvs538b ? november 2007 ? revised january 2009 functional description the lm5015 high voltage switching regulator features all the functions necessary to implement an efficient power converter using a two-switch forward or two-switch flyback topology. the voltage across the mosfets employed in the two-switch topology is clamped to the input voltage, allowing the input voltage range to approach the rating of the mosfets. the regulator control method is based upon current mode control providing cycle-by- cycle current limit, inherent input voltage feed-forward and simple feedback loop compensation. referring to figure 13 , the operating principle of the lm5015 regulator is as follows: at the beginning of each switching cycle, the oscillator sets the driver logic and turns on both the high and low side power mosfets to conduct current through the inductor or power transformer. the peak current in the mosfet is controlled by the voltage at the comp pin. the comp voltage, which is determined by the feedback circuit, is compared with the sensed current signal of the internal low side power mosfet. when the current signal exceeds the comp voltage, the pwm comparator resets the driver logic, turning off both power mosfets. at the end of the switching cycle the driver logic is set again by the oscillator to initiate the next switching period. the lm5015 also contains dedicated circuitry to protect the ic from abnormal operating conditions. cycle-by- cycle current limiting prevents the power mosfet current from exceeding 1 amp. thermal shutdown circuitry holds the driver logic in reset when the die temperature reaches 165 c, and returns to normal operation when the die temperature drops by approximately 25 c. the en pin can be used as an input voltage under-voltage lockout (uvlo) during start-up to prevent operation with less than the minimum desired input voltage. bias input (vin) and power input (pvin) the lm5015 provides two separate input power pins, vin and pvin, allowing for flexible decoupling options. the vin pin provides power to the low drop-out vcc bias regulator which powers all internal control blocks. the pvin connects directly to the high side mosfet drain. if used with a single input source, the recommended configuration is shown in figure 2a . separate input pins allow the bias input (vin) to be de-coupled from the main power input as shown. it is possible to directly connect the vin and pvin pins for applications with localized de-coupling capacitors. for applications where a lower voltage auxiliary source is available, the configuration shown in figure 2b can be used. powering the vin pin with a relatively low voltage auxiliary source reduces the ic power dissipation and increases the conversion efficiency, especially when the main power source for pvin is relatively large. the vin and pvin pins are independent and can be separately biased at any voltages within the 4.25v to 75v recommended operating range. in high voltage applications extra care should be taken to ensure that the vin and pvin pins do not exceed the absolute maximum voltage ratings of 76v. voltage ringing on the input line during line transients that exceeds the absolute maximum ratings can damage the ic. both careful pc board layout and the use of quality bypass capacitors located close to the vin and agnd pins, and to the pvin to pgnd pins, are essential. copyright ? 2007 ? 2009, texas instruments incorporated submit documentation feedback 9 product folder links: lm5015
lm5015 snvs538b ? november 2007 ? revised january 2009 www.ti.com figure 14. analog and power input ports the pvin and pgnd pins are internally connected to the high and low side power mosfets, respectively. when designing the pc board, the input filter capacitor should connect directly to these pins with short connection traces. the vin operating range is 4.25v to 75v. the current drawn into the vin pin depends primarily on the gate charge of the internal power mosfets, the switching frequency, and any external load on the vcc pin. it is recommended that a small filter shown in figure 14 be used for the vin input to suppress transients which may occur at the input supply. this is particularly important when vin is operated close to the maximum operating rating of the lm5015. high voltage vcc regulator the lm5015 vcc low drop out (ldo) regulator allows the lm5015 to operate at the lowest possible input voltage. when power is applied to the vin pin and the en pin voltage is greater than 0.45v, the vcc regulator is enabled, supplying current into the external capacitor connected to the vcc pin. when the vin voltage is between 4.25v and 6.9v, the vcc voltage is approximately equal to the vin voltage. when the voltage on the vin pin exceeds 6.9v, the vcc pin voltage is regulated at 6.9v. the total input operating range of the vcc ldo regulator is 4.25v to 75v. the output of the vcc regulator is current limited to 20ma. during power-up, the vcc regulator supplies current into the required decoupling capacitor (0.47 f or greater ceramic capacitor) at the vcc pin. when the voltage at the vcc pin exceeds the vcc uvlo threshold of 3.75v and the en pin is greater than 1.26v the pwm controller is enabled and switching begins. the controller remains enabled until vcc falls below 3.60v or the en pin falls below 1.16v. an auxiliary supply voltage can be applied to the vcc pin to reduce the ic power dissipation. if the auxiliary voltage is greater than 6.9v, the internal regulator will essentially shutoff, and internal power dissipation will be decreased by the vin-vcc voltage difference times the operating current. the externally applied vcc voltage should not exceed 14v. the vcc regulator series pass mosfet includes a body diode (see figure 13 ) between vcc and vin that should not be forward biased in normal operation. therefore, the auxiliary vcc voltage should never exceed the vin voltage. 10 submit documentation feedback copyright ? 2007 ? 2009, texas instruments incorporated product folder links: lm5015 10 : lm5015 vin pvin agnd pgnd (a) analog input powered from the main power lm5015 vin pvin agnd pgnd (b) analog input powered from a separate bias source v pwr 0.1 p f v pwr as v bi 0.1 p f
lm5015 www.ti.com snvs538b ? november 2007 ? revised january 2009 high side bootstrap bias the high side bootstrap bias provides power to drive the high side power mosfet. an external capacitor is required between the bst and the ho pins. a minimum capacitor value of 0.022 f is recommended. the capacitor is charged from vcc via an internal diode during each power mosfet off-time. oscillator a single external resistor connected between rt and agnd pins sets the lm5015 oscillator frequency. to set a desired oscillator frequency (f sw ), the necessary value for the r t resistor can be calculated from the following equation: (1) the tolerance of the external resistor and the frequency tolerance indicated in the electrical characteristics table must be taken into account when determining the total variation of the switching frequency. external synchronization the lm5015 can be synchronized to the rising edge of an external clock. because the oscillator uses a divide- by-two circuit, the switching frequency f sw in the above equation is actually half the native oscillator frequency. therefore, in order to synchronize, the external clock must have a frequency higher than twice the free running f sw set by the r t resistor. the clock signal should be coupled through a 100 pf capacitor into the rt pin. a peak voltage level greater than 3.2v at the rt pin is required for detection of the sync pulse. the dc voltage across the r t resistor is internally regulated at 1.5 volts. the negative portion of the ac voltage of the synchronizing clock is clamped to 1.5v by an amplifier inside the lm5015 with approximately 100 ? output impedance. therefore, the ac pulse superimposed on the r t resistor must have positive pulse amplitude of 1.7v or greater to successfully synchronize the oscillator. the sync pulse width measured at the rt pin should have a duration greater than 15 ns and less than 5% of the switching period. the r t resistor is always required, whether the oscillator is free running or externally synchronized. the r t resistor should be located very close to the device and connected directly to the rt and agnd pins of the lm5015. enable / standby the lm5015 contains a dual level enable circuit. when the en pin voltage is below 0.45v, the ic is in a low current shutdown mode with the vcc ldo disabled. when the en pin voltage is raised above the 0.45v shutdown threshold but below the 1.26v standby threshold, the vcc ldo regulator is enabled, while the remainder of the ic is disabled. when the en pin voltage is raised above the 1.26v standby threshold, all functions are enabled and normal operation begins. an internal 6 a current source pulls up the en pin to activate the ic when the en pin is left disconnected. an external set-point resistor divider from vin to agnd can be used to determine the minimum operating input voltage of the regulator. the divider must be designed such that the en pin exceeds the 1.26v standby threshold when vin is in the desired operating range. the internal 6 a current source should be included when determining the resistor values. the shutdown and standby thresholds have 100 mv hysteresis to prevent noise from toggling between modes. the en pin is internally protected by a 6v zener diode through a 1 k ? resistor. the enabling voltage may exceed the zener voltage, however the zener current should be limited to less than 4 ma. error amplifier and pwm comparator an internal high gain error amplifier generates an error signal proportional to the difference between the regulated output voltage and an internal precision reference. the output of the error amplifier is connected to the comp pin allowing the user to add loop compensation, typically a type ii network, as illustrated in figure 15 . this network creates a pole at the origin that rolls off the high dc gain of the amplifier, which is necessary to accurately regulate the output voltage. a zero provides phase boost near the open loop unity gain frequency, and a high frequency pole attenuates switching noise. the pwm comparator compares the current sense signal from the current sense amplifier to the error amplifier output voltage at the comp pin. copyright ? 2007 ? 2009, texas instruments incorporated submit documentation feedback 11 product folder links: lm5015 200 khz r t = 32.4 k : x f sw (khz) - 0.8 k :
lm5015 snvs538b ? november 2007 ? revised january 2009 www.ti.com figure 15. type ii compensator when isolation between primary and secondary circuits is required, the error amplifier is usually disabled by connecting the fb pin to agnd. this allows the comp pin to be driven directly by the collector of an opto- coupler. in isolated designs the error amplifier is located on the secondary circuit and drives the opto-coupler led. the compensation network is connected to the secondary side error amplifier. an example of an isolated regulator with an opto-coupler is shown in figure 25 . current sense amplifier the lm5015 employs peak current mode control which also provides a cycle-by-cycle over current protection feature. an internal 42 milli-ohm current sense resistor measures the current in the low side power mosfet source. the sense resistor voltage is amplified 30 times to provide a 1.25v/a signal into the current limit comparator. current limiting is initiated if the internal current limit comparator input exceeds the 1.5v threshold, corresponding to 1.2a. when the current limit comparator is triggered, the ho and lo output pins immediately switches to the high impedance state. the current sense signal provides the pwm comparator with a control signal that reaches 1.5v when the mosfet current is 1.2a. to prevent erratic operation at low duty cycle, a leading edge blanking circuit attenuates the current sense signal for 100 ns when the power mosfet is turned on. when the mosfet is initially turned on, current spikes from the power mosfet drain-source and gate-source capacitances flow through the current sense resistor. these transient currents normally cease within 50 ns with proper selection of rectifier diodes and proper pc board layout. thermal protection internal thermal shutdown circuitry is provided to protect the ic in the event the maximum junction temperature is exceeded. when the 165 c junction temperature threshold is reached, the regulator is forced into a low power standby state, disabling all functions except the vcc regulator. thermal hysteresis allows the ic to cool down by 25 c before it is re-enabled. 12 submit documentation feedback copyright ? 2007 ? 2009, texas instruments incorporated product folder links: lm5015 pwm fb 1.26v 5k comp vdd 1.3v v out lm5015 r fb r 1 r 2 c 2 c 1 hz0 = 2 2 c r 2 1 x x s = ea f pole _dc zero f pole f = ? ? 1 x 2 1 2 1 c c c c 1 ? x x s 2 r 2
lm5015 www.ti.com snvs538b ? november 2007 ? revised january 2009 power mosfets the lm5015 switching regulator includes two n-channel mosfets each with 450 m ? nominal on-resistance. the drain of the high side mosfet is the pvin pin, and the source the ho pin. the drain of the low side mosfet is the lo pin, and the source is internally connected to the pgnd pin via the 42 m ? internal current sense resistor. the on-resistance of the lm5015 mosfets varies with temperature as shown in the typical performance characteristics graph. the typical gate charge for each mosfets is 4.5 nc which is supplied from the vcc and bst pins, respectively, when the mosfets are turned on. the maximum duty cycle of the power mosfets is limited less than 50%. this is achieved by an oscillator divide-by-two circuit with an additional 50 ns of forced off-time introduced between the clk and rs flip-flop. consequently, the maximum duty cycle is limited by the following equation: duty max_limit =(0.5 - 50 ns x f sw ) x 100% where ? f sw is the switching frequency in hertz (hz) (2) the purpose of limiting the maximum duty cycle less than 50% is to guarantee successful reset of the power transformer in the two-switch forward converter topology. see application information below for more detail. application information the following information is intended to provide guidelines for the power supply designer using the lm5015. two-switch forward topology two-switch forward converter, like the conventional single-switch forward converter, is derived from the buck converter topology. the main difference between a forward converter and a buck is that a power transformer is introduced in the forward converter. the transformer realizes the input-output isolation, and the turns ratio provides a means to optimize the duty cycle for the particular input and output voltage requirements of the application. the two-switch forward converter employs two power mosfet switches instead of the one switch of the single-switch forward converter. however the two-switch approach offers two major advantages over its single- switch counterpart: 1. the voltage across the power mosfet switches in a two-switch forward converter is clamped to the input voltage, allowing the input voltage range to approach the rating of the mosfets. whereas, the maximum operating voltage of a single-switch forward converter is typically limited to half the mosfet voltage rating. 2. the power transformer of a two-switch forward converter is simpler, and hence costs less, than that of a single-switch forward converter, because the two-switch converter transformer eliminates the tertiary reset winding that is normally required in the single-switch converter. figure 16 illustrates the two-switch forward converter topology. the power circuit consists of an input capacitor c in , two mosfet switches q h and q l , two clamp diodes d h and d l , a power transformer t 1 , two rectifier diodes d 1 and d 2 , an output inductor l o , and an output capacitor c o . since the lm5015 integrates both q h and q l , a low cost two-switch forward converter can be realized without a need for discrete power mosfets. with a slightly higher cost, the two rectifier diodes d 1 and d 2 on the secondary side of the power transformer can be replaced with synchronous rectifier mosfets to improve efficiency in applications with relatively low output voltage. copyright ? 2007 ? 2009, texas instruments incorporated submit documentation feedback 13 product folder links: lm5015
lm5015 snvs538b ? november 2007 ? revised january 2009 www.ti.com figure 16. two-switch forward converter topology figure 17 shows the two operating modes of the two-switch forward converter. during operation, the two mosfets are turned on and off simultaneously. the output voltage is regulated by modulating the duty cycle of the mosfets. the relationship between the input voltage v in , output voltage v out , duty cycle d, rectifier diode forward drop v f , and transformer turns ratio k is defined by the following equation. (3) when the mosfets are turned on, as shown in figure 5a , the input voltage is applied to the power transformer primary. the power transformer is magnetized by the application of the input voltage, and power flows to the secondary side circuit via transformer coupling. when the mosfets are turned off, as shown in figure 5b , the power flow to the primary is cut off. the residual magnetizing inductance of the power transformer reverses the voltage across the primary winding and forces the two clamp diodes d h and d l to conduct. this effectively clamps the mosfets voltage to the input voltage, and applies the input voltage in reversed polarity to the power transformer primary winding to demagnetize and reset the transformer. 14 submit documentation feedback copyright ? 2007 ? 2009, texas instruments incorporated product folder links: lm5015 k x (v out + v f ) d = v in v in v out c in q h q l d l d h t 1 d 1 d 2 l o c o k:1
lm5015 www.ti.com snvs538b ? november 2007 ? revised january 2009 figure 17. operating modes of two-switch forward converter note that the power transformer primary receives the voltage of the nearly equal magnitude but opposite polarities during the on and off period of the power mosfets. in order to guarantee the volt-second balance between the magnetizing and demagnetizing intervals, the lm5015 limits the maximum duty cycle less than 50%. therefore, an lm5015 two-switch forward regulator always achieves a complete reset of the power transformer during each switching cycle. the lm5015 can also be used to implement a two-switch flyback regulator ( figure 26 ). the voltage across the mosfets employed in the two-switch flyback converter is also clamped to the input voltage, allowing the input voltage range to approach the rating of the mosfets. generally the flyback converter is simpler and costs less than the forward converter. however, the flyback converter will have higher ripple current and voltages, and the conversion efficiency is typically lower. copyright ? 2007 ? 2009, texas instruments incorporated submit documentation feedback 15 product folder links: lm5015 (a) current paths when mosfets are turned on (b) current paths when mosfets are turned off v in v out on on v in v out off off
lm5015 snvs538b ? november 2007 ? revised january 2009 www.ti.com en / uvlo voltage divider selection two dedicated comparators connected to the en pin are used to implement input under-voltage lockout and a shutdown condition. when the en pin voltage is below 0.45v, the controller is in a low current shutdown mode where the vin current is reduced to 110 a. for an en pin voltage greater than 0.45v but less than 1.26v the controller is in standby mode, with all internal circuits operational, but with the power mosfets disabled. once the en pin voltage is greater than 1.26v, the controller is fully enabled and the ho and lo outputs commence switching. two external resistors can be used to program the minimum operational voltage for the power converter as shown in figure 18 . when the en pin voltage falls below the 1.26v threshold, an internal 100 mv threshold hysteresis prevents noise from toggling the state. therefore, the voltage at the en pin must be reduced to 1.16v to transition to the standby state. resistance values for r1 and r2 can be determined from the following equations, where v pwr is the desired turn-on voltage and i divider is the user-defined current through r1 and r2. (4) for example, if the lm5015 is to be enabled when v pwr reaches 16v, i divider could be chosen as 500 a which would set r1 to 29.4 k ? and r2 to 2.49 k ? . if the voltage at the en pin can exceed 6v, then the current into the 6v protection zener must be limited below 4 ma by the external resistors. be sure to check both the power and voltage rating for the selected r1 resistor (some 0603 resistors are rated as low as 50v maximum operating voltage). figure 18. basic en (uvlo) configuration a remote enable function can be accomplished with open drain device(s) connected to the en pin as shown in figure 19 . a mosfet or an npn transistor connected to the en pin will force the regulator into the low power ? off ? state. adding a pn diode in the drain (or collector) provides the offset to achieve the standby state. the advantage of standby is that the vcc ldo is not disabled and external circuitry powered by vcc remains functional. 16 submit documentation feedback copyright ? 2007 ? 2009, texas instruments incorporated product folder links: lm5015 en lm5015 v pwr 1.26v 6 p a standby (disable pwm controller) r1 r2 0.45v shutdown vcc ldo vin 6v 1k v pwr - 1.26v r1 = i divider 1.26v r2 = i divider + 6 p a
lm5015 www.ti.com snvs538b ? november 2007 ? revised january 2009 figure 19. remote standby and disable control soft-start soft-start is implemented with an external capacitor c ss connected to the ss pin as shown in figure 20 . the ss discharge mosfet conducts during shutdown and standby modes. when the ss pin is low, the comp voltage is held below the pwm offset voltage (1.3v) by the ss buffer amplifier, thus inhibiting pwm pulses. when the en pin exceeds the 1.26v standby threshold, the enable signal will turn-off the ss discharge mosfet and allow the internal 11 a current source to charge the ss capacitor. the comp voltage will follow the ss voltage under the control of the open-drain ss buffer amplifier. the c ss capacitor will cause the comp voltage to gradually increase, until the output voltage achieves regulation, and the error amplifier assumes control of the comp and the pwm duty cycle. the c ss capacitor continues charging by the internal 11 a current source, preventing the ss voltage from interfering with the normal error amplifier function. during shutdown, the ss discharge mosfet conducts to discharge the c ss capacitor. figure 20. soft-start copyright ? 2007 ? 2009, texas instruments incorporated submit documentation feedback 17 product folder links: lm5015 comp ss soft-start capacitor lm5015 c ss 11 p a enable vdd pwm current limit 1.5v 1.3v vdd (5v) 1.26v 5k fb v out en lm5015 v pwr 1.26v standby r1 r2 0.45v shutdown off standby
lm5015 snvs538b ? november 2007 ? revised january 2009 www.ti.com conventional isolated output feedback designs when isolation between the primary and secondary circuits is required, the internal error amplifier is usually disabled by connecting the fb pin to agnd, and an external error amplifier is employed on the secondary side of the isolation boundary. an opto-coupler is normally used to send the feedback signal across the isolation boundary, as shown in figure 21 . the lm5015 provides built-in pull-up for the collector of the opto-coupler at the comp pin through a 5 k ? internal resistor. similar compensation network used in figure 15 is applicable to the external, secondary-side error amplifier. the lm431a shown in figure 21 provides both the voltage reference and error amplifier required to regulate the isolated output voltage. figure 21. conventional isolated feedback high bandwidth isolated feedback design using the cfb pin the lm5015 also includes a current mirror circuit for optional high bandwidth feedback loop design. as shown in figure 22 , the emitter of the opto-coupler transistor can be connected to the cfb pin, and the collector connected to vcc through an external 1 k ? resistor. the 1 k ? resistor to vcc is used to protect the cfb pin by limiting the opto-coupler current to less than 10 ma. the 1 k ? resistor from the opto-coupler collector to ground is introduced to protect the opto-coupler from excess voltage by limiting its v ce to less than 50% of vcc max. when the output voltage is below regulation, no current flows into the cfb pin and the pwm of the lm5015 operates at maximum duty cycle. 18 submit documentation feedback copyright ? 2007 ? 2009, texas instruments incorporated product folder links: lm5015 pwm fb 1.26v 5k comp vdd 1.3v v out lm5015 ea lmv431a agnd r o1 r o2
lm5015 www.ti.com snvs538b ? november 2007 ? revised january 2009 figure 22. high bandwidth isolated feedback using cfb pin the two external pull-up and pull-down resistors are effectively connected in parallel for ac signal, yielding a collector resistance on the opto-coupler of 0.5 k ? . this resistance is 10 times smaller than the internal pull up resistor and the pole associated with the collector-base capacitance of the opto-coupler transistor is pushed out to a decade higher frequency. moving the opto-coupler pole to a higher frequency allows higher loop bandwidth capability than conventional isolated feedback designs (see figure 21 ). output voltage output voltage is normally set with a resistor divider shown in figure 23 . to set the regulator ? s output voltage to v o , the two resistors must satisfy the following equation: where ? v ref is the reference voltage of the error amplifier, which is 1.26v for the lm5015 ? s internal error amplifier (5) figure 23. output voltage setting in isolated designs, the reference and error amplifier are located on the secondary side. to obtain a 5v output in an isolated feedback design using lmv431a (whose nominal v ref is1.24v), the feedback divider resistors ratio specified by above equation is 0.330. selecting 24.3 k ? for r o1 , then r o2 should be 8.06 k ? . in a similar non- isolated converter design using the internal error amplifier, the divider ? s resistors ratio is 0.337, therefore if 24.3 k ? is selected for r o1 , then r o2 should be 8.20 k ? . copyright ? 2007 ? 2009, texas instruments incorporated submit documentation feedback 19 product folder links: lm5015 error amplifier (internal or external) v ref v o r o1 r o2 v ref = v o - v ref r o2 r o1 fb comp lm5015 cfb vcc 1k lmv431a 1k current mirror pwm 1.26v 5k vdd 1.3v ea v out r o1 r o2
lm5015 snvs538b ? november 2007 ? revised january 2009 www.ti.com multiple resistors in series or parallel combinations for either r o1 , or r o2 , or both, may be necessary to set a required output voltage. note that the accuracy of the output voltage setting is determined by the tolerance of the divider resistors as well as the accuracy of v ref . the accuracy of the lm5015 internal v ref is 1.5%, and the most popular chip resistors have a tolerance of 1%, therefore the achievable output accuracy with the internal error amplifier and 1% resistors is about 2.5%. to achieve better output voltage accuracy, use an external voltage reference with higher precision and resistors of tighter tolerance, such as the 0.1%, resistors for r o1 and r o2 . printed circuit board layout the lm5015 current sense and pwm comparators are very fast and may respond to short duration noise pulses. the components at the ho, lo, comp, en, vcc and the rt pins should be as physically close as possible to the ic, thereby minimizing noise pickup on the pc board tracks. the ho and lo output pins of the lm5015 should have short, wide conductors to the power path inductors, transformers and capacitors in order to minimize parasitic inductance that reduces efficiency and increases conducted and radiated noise. ceramic decoupling capacitors are recommended between the vin pin to the agnd pin, between the pvin pin and pgnd pin, and between the vcc pin to the agnd pin. use short, direct connections to avoid clock jitter due to ground voltage differentials. small package surface mount x7r or x5r capacitors are preferred for high frequency performance and limited variation over temperature and applied voltage. if an application using the lm5015 produces high junction temperatures during normal operation, multiple vias from the exposed metal pad on the underside of the ic package to a pc board ground plane will help conduct heat away from the ic. judicious positioning of the pc board within the end product, along with use of any available air flow will help reduce the junction temperature. if using forced air cooling, avoid placing the lm5015 in the airflow shadow of large components, such as input or output capacitors, inductors or transformers. application examples the following schematics present four examples dc-dc converters utilizing the lm5015 switching regulator ic: 1. non-isolated two-switch forward for 48v input and 5v 2.5a output, 2. isolated two-switch forward for 48v input and 5v 2.5a output 3. isolated two-switch flyback converter for 48v input and 5v 2.5a output, 4. a 1:1 dc-dc transformer with the input/output operating range of 5v to 15v 48v non-isolated two-switch forward the non-isolated two-switch forward converter shown in figure 24 utilizes the internal voltage reference for the regulation set-point. the output is +5v at 2.5a while the input voltage can vary from 36v to 72v. the switching frequency is 300 khz. an auxiliary winding on transformer (t1) provides 10v to power the lm5015 when the output is in regulation. this disables the internal high voltage vcc ldo regulator and improves efficiency. the converter can be shut down by driving the en input below 1.26v with an open-collector or open-drain transistor. an external synchronizing frequency can be applied to the sync input. figure 24. non-isolated two-switch forward 20 submit documentation feedback copyright ? 2007 ? 2009, texas instruments incorporated product folder links: lm5015
lm5015 www.ti.com snvs538b ? november 2007 ? revised january 2009 48v isolated two-switch forward the isolated two-switch forward converter shown in figure 25 utilizes a 1.24v voltage reference (lmv431a) located on the isolated secondary side for the regulation set-point. the lm5015 internal error amplifier is disabled by grounding the fb pin. the lmv431a controls the current through the opto-coupler led, which sets the comp pin voltage. the output is +5v at 2.5a and the input voltage ranges from 36v to 72v. the switching frequency is 300 khz. the functions of the en and sync inputs are the same as in the previous example circuit. figure 25. isolated two-switch forward isolated two-switch flyback the isolated two-switch flyback converter shown in figure 26 utilizes a 1.24v voltage reference (lmv431a) located on the isolated secondary side for the regulation set-point. the lm5015 internal error amplifier is disabled by grounding the fb pin. the lmv431a controls the current through the opto-coupler led, which sets the comp pin voltage. the output is +5v at 2.5a and the input voltage ranges from 36v to 72v. the switching frequency is 300 khz. the flyback converter is less complex than the previous forward converter example in figure 25 . however, the flyback converter produces higher input and output ripples of voltage and currents, and lower conversion efficiency by about 2%. the functions of the en and sync inputs are the same as in the previous example circuits. this circuit can be used with the lm5073 for a low cost isolated power over ethernet (poe) power device (pd) application that does not require a discrete power mosfet. copyright ? 2007 ? 2009, texas instruments incorporated submit documentation feedback 21 product folder links: lm5015
lm5015 snvs538b ? november 2007 ? revised january 2009 www.ti.com figure 26. isolated two-switch flyback dc-dc transformer the dc-dc transformer shown in figure 27 provides a 1:1 input voltage to output voltage conversion with ground isolation. the circuit operates in open loop manner operating at the maximum duty cycle limit of the lm5015. the power transformer primary-secondary turns ratio is 1:2 (primary to secondary). therefore, at the maximum duty cycle of 0.5, the output voltage will be approximately equal to the input voltage. a zener diode z1 is used at the output rail as a simple means to protect the output against over-voltage under light and no load conditions. the maximum load of this example circuit is 0.3a, and the operating voltage range is from 5v to 15v. figure 27. dc-dc transformer 22 submit documentation feedback copyright ? 2007 ? 2009, texas instruments incorporated product folder links: lm5015
package option addendum www.ti.com 24-jan-2013 addendum-page 1 packaging information orderable device status (1) package type package drawing pins package qty eco plan (2) lead/ball finish msl peak temp (3) op temp (c) top-side markings (4) samples lm5015mh/nopb active htssop pwp 14 94 green (rohs & no sb/br) cu sn level-1-260c-unlim -40 to 125 lm5015 mh lm5015mhe/nopb active htssop pwp 14 250 green (rohs & no sb/br) cu sn level-1-260c-unlim -40 to 125 lm5015 mh lm5015mhx/nopb active htssop pwp 14 2500 green (rohs & no sb/br) cu sn level-1-260c-unlim -40 to 125 lm5015 mh (1) the marketing status values are defined as follows: active: product device recommended for new designs. lifebuy: ti has announced that the device will be discontinued, and a lifetime-buy period is in effect. nrnd: not recommended for new designs. device is in production to support existing customers, but ti does not recommend using this part in a new design. preview: device has been announced but is not in production. samples may or may not be available. obsolete: ti has discontinued the production of the device. (2) eco plan - the planned eco-friendly classification: pb-free (rohs), pb-free (rohs exempt), or green (rohs & no sb/br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. tbd: the pb-free/green conversion plan has not been defined. pb-free (rohs): ti's terms "lead-free" or "pb-free" mean semiconductor products that are compatible with the current rohs requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. where designed to be soldered at high temperatures, ti pb-free products are suitable for use in specified lead-free processes. pb-free (rohs exempt): this component has a rohs exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. the component is otherwise considered pb-free (rohs compatible) as defined above. green (rohs & no sb/br): ti defines "green" to mean pb-free (rohs compatible), and free of bromine (br) and antimony (sb) based flame retardants (br or sb do not exceed 0.1% by weight in homogeneous material) (3) msl, peak temp. -- the moisture sensitivity level rating according to the jedec industry standard classifications, and peak solder temperature. (4) only one of markings shown within the brackets will appear on the physical device. important information and disclaimer: the information provided on this page represents ti's knowledge and belief as of the date that it is provided. ti bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. efforts are underway to better integrate information from third parties. ti has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. ti and ti suppliers consider certain information to be proprietary, and thus cas numbers and other limited information may not be available for release. in no event shall ti's liability arising out of such information exceed the total purchase price of the ti part(s) at issue in this document sold by ti to customer on an annual basis.
tape and reel information *all dimensions are nominal device package type package drawing pins spq reel diameter (mm) reel width w1 (mm) a0 (mm) b0 (mm) k0 (mm) p1 (mm) w (mm) pin1 quadrant lm5015mhe/nopb htssop pwp 14 250 178.0 12.4 6.95 8.3 1.6 8.0 12.0 q1 lm5015mhx/nopb htssop pwp 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 q1 package materials information www.ti.com 17-nov-2012 pack materials-page 1
*all dimensions are nominal device package type package drawing pins spq length (mm) width (mm) height (mm) lm5015mhe/nopb htssop pwp 14 250 203.0 190.0 41.0 lm5015mhx/nopb htssop pwp 14 2500 349.0 337.0 45.0 package materials information www.ti.com 17-nov-2012 pack materials-page 2
mechanical da t a pwp0014a www .ti.com m x a 1 4 a ( r e v a )
important notice texas instruments incorporated and its subsidiaries (ti) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per jesd46, latest issue, and to discontinue any product or service per jesd48, latest issue. buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. all semiconductor products (also referred to herein as ? components ? ) are sold subject to ti ? s terms and conditions of sale supplied at the time of order acknowledgment. ti warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in ti ? s terms and conditions of sale of semiconductor products. testing and other quality control techniques are used to the extent ti deems necessary to support this warranty. except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. ti assumes no liability for applications assistance or the design of buyers ? products. buyers are responsible for their products and applications using ti components. to minimize the risks associated with buyers ? products and applications, buyers should provide adequate design and operating safeguards. ti does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which ti components or services are used. information published by ti regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from ti under the patents or other intellectual property of ti. reproduction of significant portions of ti information in ti data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. ti is not responsible or liable for such altered documentation. information of third parties may be subject to additional restrictions. resale of ti components or services with statements different from or beyond the parameters stated by ti for that component or service voids all express and any implied warranties for the associated ti component or service and is an unfair and deceptive business practice. ti is not responsible or liable for any such statements. buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of ti components in its applications, notwithstanding any applications-related information or support that may be provided by ti. buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. buyer will fully indemnify ti and its representatives against any damages arising out of the use of any ti components in safety-critical applications. in some cases, ti components may be promoted specifically to facilitate safety-related applications. with such components, ti ? s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. nonetheless, such components are subject to these terms. no ti components are authorized for use in fda class iii (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. only those ti components which ti has specifically designated as military grade or ? enhanced plastic ? are designed and intended for use in military/aerospace applications or environments. buyer acknowledges and agrees that any military or aerospace use of ti components which have not been so designated is solely at the buyer ' s risk, and that buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. ti has specifically designated certain components as meeting iso/ts16949 requirements, mainly for automotive use. in any case of use of non-designated products, ti will not be responsible for any failure to meet iso/ts16949. products applications audio www.ti.com/audio automotive and transportation www.ti.com/automotive amplifiers amplifier.ti.com communications and telecom www.ti.com/communications data converters dataconverter.ti.com computers and peripherals www.ti.com/computers dlp ? products www.dlp.com consumer electronics www.ti.com/consumer-apps dsp dsp.ti.com energy and lighting www.ti.com/energy clocks and timers www.ti.com/clocks industrial www.ti.com/industrial interface interface.ti.com medical www.ti.com/medical logic logic.ti.com security www.ti.com/security power mgmt power.ti.com space, avionics and defense www.ti.com/space-avionics-defense microcontrollers microcontroller.ti.com video and imaging www.ti.com/video rfid www.ti-rfid.com omap applications processors www.ti.com/omap ti e2e community e2e.ti.com wireless connectivity www.ti.com/wirelessconnectivity mailing address: texas instruments, post office box 655303, dallas, texas 75265 copyright ? 2013, texas instruments incorporated
mouser electronics authorized distributor click to view pricing, inventory, delivery & lifecycle information: texas instruments: ? lm5015isoeval? lm5015mh/nopb? lm5015nisoeval

▲Up To Search▲

Price & Availability of LM5015-14

	To Download LM5015-14 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .